For sale is a Hella rear fog light set. This probably was made in the 1980's. It could also be a 3rd brake light if anyone wanted to do that with it. It has a plastic lens and housing, a switch amd a short wiring harness. All of this si enclosed in the original styrofoam and cardboard package. It is a neat 80's period accessory. Thanks for your interest! I accept Paypal. Garrett
For sale is a pair of late '60's early '70's 911 bumper guards, also called overriders. This pair of bumper guards is in good cosmetic condition, with fair to goog original chrome. Earh has a few small dents on the outside and surface rust on the inside, reflecting their age. However for original parts, they are in good condition. They would be very good candidates for replating. Please write i...
For sale are 14 new Tenax faasteners for attaching to your top or toneau cover. Included are 2 body studs. These are new and were purchased from Stoddard. Paypal accepted. I will cover shipping. Thank you for looking! Garrett
Here is a newly plated round chrome bezel likely for the under dash power plug recepticle. The ID is smooth and 11 mm. in diameter. The outer surface, which rests behind the dash, is threaded. The exposed face of the bezel tapers at about a 40 degree angle and is not curved. This is leading me to believe it is not for a light switch or other dash switch. Thanks for your interest. Garrett
For sale is a steering column horn contact assembly for a 356A. It is an original and is in excellent condition, with no brush wear. This fits on the side of the steering column, under the dash. It is not located near the horn button itself. Thanks for your interest!
For sale is the right hand side half of an aluminum 356A turn signal housing. It has an SWF logo cast inside and it is original. There is a little tan paint left, but you can paint to your liking to match the left half, which covers the switch. Thanks for your interest. There will be a small charge for shipping, depending on your location.
For sale are 3 356 A turn signal switch housings. Specify which you would like, all paint, chipped paint, or no paint. These are originals, manufactured by SWF. Shipping will be added to the total. Paypal accepted. Thanks for looking, Garrett
Here are 4 new door striker shims for fitting between the striker and the body on a 356A T2, 356B and 356C. These are new. Thanks for looking.
For sale is a hard to find 356C left axle tube bump stop bracket. I welded a rust problem this had, sandblasted and primed it. It is ready to use. This has the provision for holding the handbrake cable's outer housing, which earlier ones did not. Price will have shipping added. Paypal accepted. Thanks for looking! Garrett
For sale is a NOS part. It is an original Bosch pinion gear for a starter. The remains of the box do not show a part number. On the gear are stamped ALG 30 1 LZ The pinion gear has 9 teeth. Is there anyone that could tell me what this fits? Thanks! Garrett
For sale is a VW style jack. It lived with our 356 for most of the car's life, but it is actually a style that would have been sold with an early VW. It was painted and has not been used in a long time. Best offer. Shipping will be added to the total. Paypal accepted. Thank you for your interest. Garrett
For sale is a 356A wiper motor. Weather it functions or not is unknown. Use for a core, conversion or clean up and test. Best offer. Cover is in good condition. Paypal accepted, shipping additional. Thanks for looking, Garrett
For sale is a small collection of parts that make up the handbrake cable "splitter". Theae parts join the front half in the trans tunnel, to the rear cables that exit to the wheels.. I hope these help someone who is putting a car back together from the ground up! Paypal accepted, shipping additional. Thanks for looking, Garrett
For sale is a rebuilt 912 Bosch starter. It will fit '66 to '69 models. I was going to fit it to a 356 until I discovered that there were problems with flywheel size and an interference with the body. This starter is ready to use and I would like to pass it on to someone that could use it! Paypal accepted, shipping additional. Thanks for looking, Garrett
For sale is the junction block from an original 356 pre formed fuel line. The lines have been shortened. Use this to build your own custom formed fuel line, perhaps for Weber carbs. Paypal accepted. Thanks for looking! Garrett
For sale is a throttle linkage cross bar. It has been sandblasted and painted. It is ready to use! Shipping will be additional. Paypal accepted. Thanks for looking! Garrett
For sale are 2 of the "Norma" oil filter canister retaining straps for $15 each. You have a choice of original nickel plating, or yellow cad plating. Payapl accepted. Shipping additional. Thanks for looking. Garrett
Returns Accepted: Returns Accepted Item must be returned within: 14 Days Refund will be given as: Money Back Return policy details: If I misrepresented the item in some way or it is unusable as shipped Return shipping will be paid by: Buyer Restocking Fee: No This is my last one of these. I have tried to discern the exact applications to the best of my limited mopar knowledge . Please use your ...
Item must be returned within: 14 Days Refund will be given as: Money Back Return shipping will be paid by: Buyer Returns Accepted: Returns Accepted Return policy details: If I misrepresented the item in some way or it is unusable as shipped Restocking Fee: No CHECK OUT MY MUSIC DOUGNYE.COM Also, Check out my store for some good deals on antique auto parts. HERE I AM OFFERING FOR SALE one new Ge...
Returns Accepted: Returns Accepted Item must be returned within: 14 Days Refund will be given as: Money Back Return policy details: If I misrepresented the item in some way or it is unusable as shipped Return shipping will be paid by: Buyer Restocking Fee: No Here I am offering for sale lot of 6 fuel filters manufactured by AC Part #TP571 same as wix part#33106 same as Gm#6435501 Height: 4.778 ...